How to use 10 print fingerprint scanner? | HFSecurity

Device Driver Installation

Insert the software CD into the CD-ROM drive. You will see the following three folders.

Go to Windows>Driver>Setup and double click on “Setup” to start the installation, you will see

Click the “Next>” button to continue and you will see the following pop-up window

Click on “Change… ” to select the folder where you want to install the software, and then click the “Next>” button. Or, just click the “Next>” button and continue using the default path, then you will see 

Click the “Install” button to start installing the driver, then you will see the following pop-up window.

Click the “Finish” button to complete the installation.

Using the demo software

Initial Screen

Run the “Demo” software and you will see the following on the initial screen

Attention.

Flat finger. Acquisition of a single plain fingerprint image

Curled Finger. Capture a single curled fingerprint image

Four-finger slap. Capture fingerprints from four fingers on the left and right side and two thumbs.

4-4-2, 10 planes. Collect 10 planes with four finger taps and two thumbs.

4-4-2, 10 rolls. Capture 10 rolls, 4 finger taps and two thumbs.

Splitting. Split 4 finger taps into discrete single-finger images

Open. Starts and activates a capture mode

Save. Saves the captured image to the local computer

Stop: Turns off the current scanning option

Exit. Closes the scanning demo software

apturing fingerprints

IMPORTANT: If your finger is too wet, it is recommended that you place your finger on the platen to avoid blurring or smudging the image.

NOTE: If your finger is too wet, it is recommended that you place your finger on the platen to avoid blurring or smudging of the image. Ensure that most of the fingerprint cores appear and are captured.

Make sure that most of the fingerprint cores appear and are captured. If your finger is too dry, it is recommended that you place your finger on the platen and place your finger on the platen appropriately.

If your finger is too dry, it is recommended to place the finger firmly on the platen and apply appropriate pressure so that the operator can obtain a clear, legible fingerprint print.

Clear, readable fingerprint impressions ……

– Taking a single finger flat fingerprint

Step 1: Select “Flat Finger” and click “Open” to enter the idle screen

Step 2: Select “Flat Finger”, then click “Open” to enter the idle interface. Place one finger on the platen to start the acquisition.

Step 3. Click the “Save” button to save the captured image.

Step 4. Click the “Stop” button to terminate the current scanning option

Capturing Rolled Finger

Step 1: Select “Roll Finger” and click “Open” to enter the idle screen.

Step 2. Place one finger on the platen to roll

Step 3. Click the “Save” button to save the captured image.

Step 4. Click the “Stop” button to terminate the current scanning option

Caution.

There are two ways to roll your finger during the capture process.

1) Nail to Nail

2) Nail to Nail Rolling

When a rolling fingerprint image is captured using the Nail to Nail method, one side of the bulbous portion of the finger (fingertip to fingertip) appears on the screen.

When acquiring a rolling fingerprint image using the “nail-to-nail” method, place one side of the finger (fingertip to just below the first joint) on the platen and roll the finger with light, even pressure.

With even pressure, then roll the finger to the other side (nail to nail) until it is facing the opposite direction.

Capturing 4 Finger Slaps

Step 1: Select “4 Finger Slaps”, then click “Open” to get in idle screen

Step 2. Place left or right slap on the platen to start capturing

Step 3. Click “Save” button to save the captured image

Step 4. Click “Stop” button to terminate the current scan option

Note:

When Slap Option-Segmentation is chosen, the 4 finger slaps will be segmented into discrete single fingerprint image automatically. The single image will be stored under default installation director

Capturing 10 Finger Flats, 4 Finger Slaps and 2 Thumbs

Step 1: Select “4-4-2, 10 Flats”, then click “Open” to get in idle screen

Step 2. Place the right finger and slap on the platen to start capturing

Capturing 10 Finger Rolls, 4 Finger Slaps and 2 Thumbs

Step 1: Select “4-4-2, 10 Rolls”, then click “Open” to get in idle screen

Step 2. Place the right finger and slap on the platen to start capturing

HOW TO PLACE FINGER ON THE PLATEN PROPERLY

When capturing fingerprints (single flats, rolls, 4 finger slaps and 2 thumbs slap), make sure the fingers are placed slightly with proper pressure at the center of the platen from bottom part.

. Maintenance

It is recommended to clean the rollers before shooting to ensure high quality images are printed.

When cleaning the platen, please read the following.

-Use a cleaning cloth to wipe the platen. Make sure the cleaning cloth is clean, but not wet or dripping.

-Make sure the cleaning cloth is clean, but not wet or dripping. Pay special attention to the corners and edges of the window where dust may be present.

Pay special attention to the corners and edges of windows where dust may collect.

-Never spray the cleaning solution directly onto the platen!

-Make sure to spray on a cloth and then wipe.

Always spray on a cloth and then wipe with a cloth

Then wipe the reader with a cloth. If you spray the cleaning solution directly onto the reader, the cleaning solution may drip onto the main board.

If you spray the cleaning fluid directly on the reader, the cleaning fluid may drip onto the main circuit board, which may cause a short circuit and destroy the board.

-Do not make the cleaning cloth wet! If the cleaning cloth is wet, this may cause the same problem as if you sprayed the cleaner directly.

If the cleaning cloth is wet, this can cause the same problem as if you sprayed the cleaner directly on the roller.

-Never use abrasive or gritty cleaners! Abrasive cleaners may scratch the surface.

Free SDK USE